ParnupuitSawing and planing of wood · Timber building structures
About the work

From log to finished timber element

This site describes the work of PÄRNU PUIDUTÖÖSTUS OÜ, a woodworking company in Pärnu, Estonia. The company was registered on 16 November 2015 and works with sawing and planing of wood and the production of wooden parts used in building.

The pages below explain, in plain terms, how round wood becomes sawn boards, how boards are planed to exact sizes, and how timber is made into structural elements such as roof trusses, beams and wall frames.

Cutting pattern: boards from the centre of the log
Illustration: a log cross-section with a typical cutting pattern.
Primary processing

Sawing of wood

Sawing is the first step in turning logs into usable material. Logs are sorted by diameter, length and quality before cutting. Each log is then measured, and a cutting pattern is chosen so that the log gives the most useful material for its size.

The outer part of the log usually gives side boards, while the central part gives thicker pieces such as beams and planks. Bark and the rounded edges are removed and used for chips or fuel, so very little of the log goes to waste.

Log sorting

Logs are grouped by size and visible quality, which makes the cutting more even and predictable.

Cutting

Band saws or circular saws divide the log into boards, planks and square-edged beams.

Edging and trimming

Rounded edges are removed and the pieces are cut to standard lengths.

Secondary processing

Planing of wood

After drying, sawn boards are planed. A planer removes a thin layer from the surface, which makes the board smooth and gives it an exact, even thickness and width along its whole length.

Planing can be done on two or four sides. Four-sided planing gives timber with straight edges that fits together cleanly during building. Profiles such as tongue and groove, rounded corners or chamfers can be made in the same step.

  • Planed construction timber for frames and rafters
  • Profiled boards for cladding and flooring
  • Battens and laths for roofs and facades
Rough sawn board Planed board
Illustration: a board before and after the planer.
Production

Wooden building structures

Planed and graded timber is used to make load-bearing parts for houses, sheds, farm buildings and other structures. These parts are cut and assembled according to drawings, so they arrive at the building site ready to install.

Roof trusses

Triangular frames joined with metal connector plates. They carry the roof load and allow wide spans without inner walls.

Beams and rafters

Single pieces or glued sections used for floors, ceilings and roof slopes, cut to the required length and angle.

Wall frames

Pre-assembled timber frames for walls, with openings for windows and doors prepared in advance.

Roof truss with top chords, bottom chord and web members
Illustration: a simple timber roof truss.
Material

Wood species used in Estonia

Most construction timber in Estonia comes from softwood trees that grow in local forests. Each species has its own features, which affect where it is best used.

SpeciesMain featuresCommon uses
SpruceLight, even structure, easy to workFrames, trusses, battens, interior boards
PineStrong, contains resin, takes treatment wellBeams, outdoor structures, cladding
BirchHard and dense hardwoodInterior details, furniture parts
Aspen and alderSoft, low resin, stays cool to touchSauna interiors, panelling
Step by step

How the work is organised

Work on timber follows a clear order. Each step prepares the material for the next one.

  1. Receiving logs

    Logs are delivered, measured and sorted at the yard.
  2. Sawing

    Logs are cut into boards, planks and beams.
  3. Drying

    Timber is dried in kilns to a set moisture level.
  4. Planing and profiling

    Boards are planed to exact size and shaped if needed.
  5. Grading

    Pieces are checked for strength and visible defects.
  6. Assembly

    Trusses, frames and other elements are made to drawings.
Standards

Drying and quality

Moisture has a large effect on how wood behaves. Fresh wood shrinks and may twist as it dries. For this reason, construction timber is usually kiln-dried to a moisture content of about 18% or lower, and timber for interior use is dried further.

Load-bearing timber in Europe is strength graded according to the EN 14081 standard. Graded timber is given a strength class, such as C18 or C24, which tells designers and builders how much load the piece can safely carry.

Moisture control

Moisture is measured during and after drying to keep it at the target level.

Strength grading

Pieces are checked for knots, cracks and grain direction.

Storage

Finished timber is kept under cover and off the ground to stay dry.

Company details

Contact

For questions about sawing, planing or timber building structures, please use the details below.

Company
PÄRNU PUIDUTÖÖSTUS OÜ
Registry code
12948317
Registered
16.11.2015
Address
Savi tn 28, 80040 Pärnu, Pärnu maakond, Estonia
Phone
+372 442 6810
Email
[email protected]